General specifications
Design / Mounting		Cabinet installation
Installation in hazardous area		Zone 1 / Div. 2
Fieldbus connection
Power dissipation		see table 1
Main cable (Trunk)
	Rated voltage	16 ... 32 V DC , min. 15 V in case of brown out
	Rated current	trunk IN to trunk OUT max. 2 A see table 1
	Cable shield grounding option	Capacitive via 5.7 nF Direct
	Voltage drop	trunk IN to trunk OUT 100 mV max.
	Number of couplers	max. 3 per segment
	Reverse polarity protection	Built-In
Outputs
	Number of outputs	8, 10 or 12
	Number of devices per output	1
	Cable length	120 m
	Rated voltage	10 ... 14 V
	Rated current	max. 43 mA at one spur , max. 320 mA total current at all spurs
	Short-circuit current	53 mA , 1 mA in fallback state
	Cable shield grounding option	Capacitive via 4.4 nF
Surge protection		Trunk overvoltage protection if voltage exceeds typ. 39 V, max. 41 V
Diagnostic and Protection Features
Fault Isolation		Short Circuit Current Limitation at spurs Bounce Protection at spurs Signal inhibit at spurs
Physical Layer Diagnostic		Signal level at spurs Signal jitter at spurs Noise level at spurs
Indicators/operating means
Switch		S1 ON: diagnostic alarms activated S2 ON: diagnostic warnings activated S3-S8: not used
LED PWR		green: Fieldbus voltage > 16 V
LED COM/ERR		yellow flashing: fieldbus communication and physical layer status , red: Hardware error
LED SPURS		red: 2 Hz flashing in short-circuit condition
Galvanic isolation
Main wire/outputs		isolation is not affected by interference according to EN 60079-11, voltage peak value 375 V
Output/Output		No Isolation
Directive conformity
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2013
Standard conformity
Electromagnetic compatibility		NE 21:2011
Degree of protection		IEC/EN 60529
Fieldbus standard		IEC 61158-2
Climatic conditions		IEC 60721
Shock resistance		EN 60068-2-27
Vibration resistance		EN 60068-2-6
Ambient conditions
Ambient temperature		-40 ... 70 °C (-40 ... 158 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Relative humidity		< 95 % non-condensing
Shock resistance		15 g 11 ms
Vibration resistance		1 g , 10 ... 150 Hz
Corrosion resistance		acc. to ISA-S71.04-1985, severity level G3
Mechanical specifications
Connection type		screw terminal , pluggable or spring terminal , pluggable
Core cross section		see table 2
Housing material		Polycarbonate
Degree of protection		IP20
Mass		2100 g
Dimensions		see dimensions
Mounting		DIN rail mounting
Data for application in connection with hazardous areas
EU-type examination certificate		BVS 13 ATEX E 121 X
	Marking	II 2(1)G Ex eb ib mb [ia Ga] IIC T4 Gb II (1)D [Ex ia Da] IIIC I (M1) [Ex ia Ma] I
Main cable (Trunk)
	Maximum safe voltage U_m	253 V AC
Outputs		in accordance to FISCO and Entity
	Power	1.063 W
	Voltage	17.1 V
	Current	248.55 mA
	Inductance	gas group IIC 470 µH , gas group IIB 2 mH
	Capacitance	gas group IIC 367 nF , gas group IIB 2.15 µF
Directive conformity
	Directive 2014/34/EU	EN IEC 60079-0:2018+AC:2020 , EN 60079-7:2015+A1:2018 , EN 60079-11:2012 , EN 60079-18:2015
International approvals
CSA approval		CSA 14.70004139
	Control drawing	116-0400
	Approved for	Class I, Division 2, Groups A, B, C, D T4 Class I, Zone 1, AEx/Ex e ib mb [ia Ga] IIC T4 Gb Class I, Zone 1, AEx/Ex e ib mb [ia IIC Da] IIC T4 Gb Associated equipment for Class I, Division 1 Groups A, B, C, D Associated equipment for Class II, Division 1 Groups E, F, G Associated equipment for Class III, Division 1
IECEx approval		IECEx BVS 13.0119X
	Approved for	Ex eb ib mb [ia Ga] IIC T4 Gb [Ex ia Da] IIIC [Ex ia Ma] I
Certificates and approvals
FOUNDATION Fieldbus		FF-846

Are the Products Genuine OEM Units?

These items have been certified by Achievers Automation Limited to be genuine OEM Units obtained through OEM or independent third-party channels.

Does Achievers sell to international Non-USA customers?

Yes, Achievers offers services to clients around the globe. In fact, a large portion of our company is international, and we have experience shipping to locations all over the world.

Inquiry Cart 0